IFlight Beast F7 45A AIO¶
STM32F745 BGA ARM (216MHz), 1MB Flash
Integrated 4 output, BLHeli-S 45A ESC
InvenSense MPU6000 IMU (accel, gyro)
Voltage & 300A Current sensor
7.4V ~ 25V DC input power
5V 2.5A BEC for peripherals
5x PWM outputs, first 4 are internally connected to 4in1 45A BLHeli-S ESC, the fifth for LED
I2C port for external compass, airspeed sensor, etc.
8MB on board Flash for logging (set LOG_BACKEND_TYPE = 4)
Camera input/ VTX output
300A current sensor
Size and Dimensions
32.5mm x 32.5mm (25.5 x 25.5mm mount pattern)
This board has no compass and no way to connect an external compass. Applications requiring accurate heading information must rely on ArduPilots Compass-less Operation operation.
This autopilot does not have a barometer. An external barometer can be added, or operation with an alternate altitude sensor, such as GPS for outdoor use or rangefinder for indoor applications is supported (see EK3_SRC1_POSZ), with the following caveats. In Plane, if GPS is lost, then the user should switch to MANUAL mode immediately to avoid a crash. In Copter, operation is allowed using GPS, but not recommended, due to the imprecision in altitude hold modes. Bear in mind if GPS fails and the vehicle is using it for altitude information, a crash can eventually result due to lack of accurate altitude information.See Using GPS for Altitude Sensing for more information.
Default UART order¶
he UARTs are marked Rn and Tn in the above pinouts. The Rn pin is the receive pin for UARTn. The Tn pin is the transmit pin for UARTn.
SERIAL0 = console = USB
SERIAL1 = Telemetry1 = USART1 (Alternate RC input/output)
SERIAL2 = Telemetry2 = USART2 (DJI)
SERIAL3 = RC Input = USART3
SERIAL4 = GPS = USART4
SERIAL7 = USER = UART7
UART1 supports RX and TX DMA. UART2, UART3 and UART4 support RX DMA. UART7 supports TX DMA
RC input is configured by default via the USART3 RX input. It supports all RC protocols except PPM. FPort and full duplex protocols will need to use instead,both RX1 and TX1.
If the receiver is FPort or a full duplex protocol, then the receiver must be tied to the USART1 TX pin and SERIAL1_OPTIONS = 7 (invert TX/RX, half duplex), SERIAL1_PROTOCOL set to 23, and RSSI_TYPE =3.
All motor 1-4 outputs are bi-directional Dshot and PWM capable. However, mixing Dshot and normal PWM operation for outputs is restricted into groups, ie. enabling Dshot for an output in a group requires that ALL outputs in that group be configured and used as Dshot, rather than PWM outputs. The output groups that must be the same (PWM rate or Dshot, when configured as a normal servo/motor output) are: 1/4, and 2/3.
The LED pin is PWM output 5 and is default setup for use with a NeoPixel 4 led string for notifications.
The board has a built-in voltage and current sensors.
The correct battery monitor parameters are:
BATT_MONITOR = 4
BATT_VOLT_PIN = 12
BATT_VOLT_MULT ~ 10.9
BATT_CURR_PIN = 13
BATT_AMP_PERVLT ~ 100
These are set by default in the firmware.
Usually these boards are sold pre-flashed with Betaflight firmware and require both firmware and bootloader to be updated if you want to use ArduPilot. See Loading Firmware onto boards without existing ArduPilot firmware.