• Home
    • Copter
    • Plane
    • Rover
    • Sub
    • AntennaTracker
    • Mission Planner
    • APM Planner 2
    • MAVProxy
    • Companion Computers
    • Developer
  • Downloads
    • Mission Planner
    • APM Planner 2
    • Advanced User Tools
    • Developer Tools
    • Firmware
  • Community
    • Support Forums
    • Facebook
    • Developer Chat (Discord)
    • Developer Voice (Discord)
    • Contact us
    • Getting involved
    • Commercial Support
    • Development Team
    • UAS Training Centers
  • Stores
  • SWAG
  • About
    • News
    • History
    • License
    • Trademark
    • Acknowledgments
    • Wiki Editing Guide
Plane
  • Introduction
  • AutoPilot Hardware
  • First Time Setup
  • First Flight
  • If A Problem Arises
  • Flight Features
  • Advanced Configuration
    • Advanced Failsafe
    • Autopilot Output Mapping
    • Auxiliary Functions
    • Battery Voltage Compensation
    • Bootloader Update
    • CAN Bus Setup
    • Compass Setup (Advanced)
    • Crash Detection
    • Brushless ESCs
    • Extended Kalman Filter (EKF)
    • Flight Time Recorder
    • Flight Options
    • Fly-By-Wire Low Altitude Limit
    • FPort Setup
    • GeoFencing Failsafe
    • GPIOs
    • GPS for Yaw (aka Moving Baseline)
    • Ground Control Station Only Operation
    • Independent Watchdog
    • In-Flight FFT Configuration
    • Limiting Maximum Power Draw
    • LUA Scripting
    • Magnetic Interference
    • MAVLink2 Packet Signing (Security)
    • Notification Devices (LEDs,Buzzer,etc.)
    • Notch Filter Configuration
    • Object Avoidance
    • Optical Flow Sensor
    • Parameter List (Full)
    • Parameter Reset
    • RC Input Channel Mapping (RCMAP)
    • RC Options
    • Reverse Thrust Setup
    • RunCam Camera Configuration and Control
    • Sensor Position Offset Compensation
    • Sensor Testing
    • Serial Port to Port Passthrough
    • Serial Port Configuration
    • Telemetry Port Setup
    • Terrain Following
    • Transmitter Based Tuning
    • UAVCAN Setup
    • UBlox GPS Configuration
    • Vibration Damping
  • QuadPlane Support
  • Mission Planning
  • Logs
  • Peripheral Hardware
  • Use-Cases and Applications
  • Antenna Tracking
  • Simulation
  • User Alerts
  • Upcoming Features
  • Appendix
  • Fixed Wing FAQ
  • Full Table of Contents


Individual Partners SWAG Shop
 
Plane
  • Docs »
  • Advanced Configuration
  • Edit on GitHub

Advanced ConfigurationΒΆ

This section will take you through the more advanced configuration and tuning options for the vehicle.

  • Advanced Failsafe
  • Autopilot Output Mapping
  • Auxiliary Functions
  • Battery Voltage Compensation
  • Bootloader Update
  • CAN Bus Setup
  • Compass Setup (Advanced)
  • Crash Detection
  • Brushless ESCs
  • Extended Kalman Filter (EKF)
  • Flight Time Recorder
  • Flight Options
  • Fly-By-Wire Low Altitude Limit
  • FPort Setup
  • GeoFencing Failsafe
  • GPIOs
  • GPS for Yaw (aka Moving Baseline)
  • Ground Control Station Only Operation
  • Independent Watchdog
  • In-Flight FFT Configuration
  • Limiting Maximum Power Draw
  • LUA Scripting
  • Magnetic Interference
  • MAVLink2 Packet Signing (Security)
  • Notification Devices (LEDs,Buzzer,etc.)
  • Notch Filter Configuration
  • Object Avoidance
  • Optical Flow Sensor
  • Parameter List (Full)
  • Parameter Reset
  • RC Input Channel Mapping (RCMAP)
  • RC Options
  • Reverse Thrust Setup
  • RunCam Camera Configuration and Control
  • Sensor Position Offset Compensation
  • Sensor Testing
  • Serial Port to Port Passthrough
  • Serial Port Configuration
  • Telemetry Port Setup
  • Terrain Following
  • Transmitter Based Tuning
  • UAVCAN Setup
  • UBlox GPS Configuration
  • Vibration Damping
Next Previous

Questions, issues, and suggestions about this page can be raised on the forums. Issues and suggestions may be posted on the forums or the Github Issue Tracker.

Creative Commons License © Copyright 2020, ArduPilot Dev Team.